18079808826
    Home > Technology > Installation and introduction of all kinds of keel Installation and introduction of all kinds of keel


    1、 Surface decoration series: Painted keel


    All the products are made of galvanized steel plate and color steel plate, which can improve the anti rust and fireproof performance of the products and plug-in assembly, so as to make the products easy to install and improve the construction efficiency. The main ridge of the product is pressed on the reinforcing bar connecting with the edge, which improves the mechanical properties of the product and enhances its bending and twisting resistance. There are many kinds of product series for full selection.



     

    model

    Face width

    height

    length

    Groove painted keel


    Main bone with wide groove

    23

    28.5

    3000

    Narrow groove main bone

    17

    28.5

    3000

    Accessory bone with wide groove

    23

    28.5

    600

    Accessory bone with narrow groove

    17

    28.5

    600

    T-shaped painted keel


    T-shaped main bone

    24

    32

    3050

    T-shaped main bone

    24

    28.5

    3050

    T-shaped main bone

    24

    22

    3050

    T-shaped main bone

    21

    22

    3050

    T-shaped accessory bone

    24

    22

    600

    T-shaped accessory bone

    21

    15

    600

    Trimming angle


    Trimming angle

    20

    20

    3000

    Trimming angle

    15

    15

    3000

    Trimming angle

    10

    20

    3000


    Installation instructions for open installation of painted keel ceiling

    1. Determine the decorative horizontal surface, pop up the peripheral line along the horizontal line, and install the trimming angle.

    2. Determine the cross bisector, and take it as the coordinate, divide the spacing according to the design specifications, and find the lifting point.

    3. Fix wire or suspender for hoisting with nut wire.

    4. Determine the direction of keel according to the position of tuyere and lamps.

    5. Install the main bone and trimming angle and lap it vertically to cut off the surplus part.

    6. When installing, assemble the required ceiling specification, and pay attention to the connection form of main and auxiliary keel.

    7. Transfer out the level of the whole project, and lift the central part of the ceiling slightly higher than the surrounding horizontal line, so as to eliminate the illusion of central part falling caused by visual error.

    8. When installing the ceiling material, if the four sides of the edge closing part are not the specification size, cut the ceiling according to the size, and install it.

    9. Overall inspection and local adjustment to ensure the overall effect.




    Light steel keel is a kind of iron instead of wood, which has the characteristics of high strength, light weight, fire prevention and anti-corrosion. The concealed installation is fast and beautiful. It is an ideal green environmental protection material. It can provide noble and elegant new decorative materials for different grades of luxury commercial buildings, high-grade hotels, large shopping malls, airport terminal buildings, subway stations, modern office buildings of banks and large-scale purification kitchens, as well as the ceiling and wall of fashionable and elegant residential buildings.


    model

    Specifications

    U38 main keel

    U38mm*13mm*3000mm*(0.6mm-1.5mm)

    U50 main keel

    U50mm*15mm*3000mm*(0.6mm-1.5mm)

    U50 auxiliary keel

    U50mm*19mm*3000mm*(0.33mm-0.6mm)


    3、 Concealed series: light steel card keel


    The efficient and fast light steel keel includes the main keel with buckle groove and the secondary keel with buckle groove accessories. The two bottom surfaces of the main keel and the secondary keel are connected in a cross way, which is characterized in that the joint of the two main keels contains 1 / 2 standard buckle groove, and then forms a complete buckle groove structure, which is buckled in by the buckle groove of the secondary keel to realize the connection.


    Installation instructions for keel ceiling system


    1. Before the ceiling, the elevation lines shall be made on the surrounding walls, and then the large keel shall be hoisted. It is required to hang on the same horizontal plane, and then the middle keel and small keel shall be hoisted.


    2. When installing the panel, it can assist the bracket, jack up the plate and tighten the keel, and then drill holes and screw.


    3. The light steel keel ceiling should be constructed after the installation of some parts of indoor pipelines and lamps.


    4. Before construction, the non galvanized parts shall be painted with two layers of antirust paint.


    5. If the ceiling has sound absorption (insulation) requirements, the sound-absorbing (thermal insulation) material can be placed on the top of the board or pasted at the bottom of the floor. The best insulation material is felt glass wool mat or block cotton products.


    6. The distance between light steel keel and structural beam slab shall not be less than 150 mm.


    model

    Specifications

    Card type main bone

    25mm*18.5mm*3000mm*(0.5mm-1.2mm)


    4、 Partition wall series: partition keel

    The partition wall system mainly uses light steel frame as the framework, gypsum board as the surface material collocation, and applies soil filling, painting or wallpaper and other aftercare projects. Because the materials and construction methods used in the construction process avoid contact with water, it is also called dry wall compartment. Due to the characteristics of fast construction, labor saving, low cost, smooth wall surface and easy maintenance, the light steel frame of the compartment has the advantages of rapid construction, labor saving, low cost, smooth wall surface and easy maintenance.

    Technology
    Join us
    ManBetXapp下载|首页
    Contact: Huang Manager
    Tel: 0798-6688556
    Fax: 0798-6688906
    Phone: 18079808826
    Q Q:2500262266
    E-mail: july@jxyywl.com
    Address: Jiangxi Province, Leping City People's Road No. 11 (Tong Shan Industrial Park)
    Yuanyang Weili environmental protection energy saving fireproof board

    About US

    Company Honor Management idea Enterprise display Foreign marketing Enterprise News YuanYang WeiLi Production Base New product release Design potential

    Products

    Base plate series Ceiling series Glass magnesium board series Concrete style clear water board series Color whole body wall rock board series Special purpose sheet series Lightweight partition board series Glass magnesium composite duct series Passive fire board series Diatomite series

    Prefabricated

    Light steel house Sentry box Substation

    Partition

    Fire protection system Sound insulation system Quick loading system

    Join us

    Contact us 远洋威利官方公众号 Ocean Willie official public number
      YUANYANG WEILIYUANYANG WEILI
    ManBetXapp下载|首页  Industry identification quality  Customers rely on the quality of domestic well-known brands  赣ICP备13004127号
    Zip: 333300  Tel: 0798-6688556  Phohe: 18079808826  E-mail: july@jxyywl.com  Url: www.jxyywl.com